![]() Steel posts can be supplied in almost all shapes: T-post, Y-post, L-post, Studded T post, U channel post and various tubular posts. The posts are available in lengths varying from 5 to 8 feet in 6-inch increments. Galvanized steel fence posts are light in weight, fireproof, extremely durable, and relatively easy to drive. The zinc plating finish offers better corrosion resistance property to the steel posts. Either galvanized iron or hot dipped galvanized (HDG) steel posts. Steel Fence Posts Galvanized with Zinc Plating Fencing accessories include barbed wire, concertian wire, wire nails, tie wire and others.Īccording to Finishes, Fence Posts are classified into FIVE major types:ġ. Mesh fences are galvanised mesh fence, welded mesh, chain link mesh, curved mesh, field fence, fence gates. Steel posts we supply are mainly Australia style, USA style and Euro style and many types to fit the metal fences to be installed and fixed. Tighten all hardware to secure Top & Bottom Tracs to Post Tracs.Dongfang is a China supplier of steel fence post, coated fence post, Y- post, T-post, pipe post with mesh fences, and various fencing accessories.Place Top Trac over Post Tracs, and align slotted holes.Infill materials are held in place by Tracs & do not require mechanical fastening.Sheet rock beads can be used as spacers for installations with infill materials 3/4” thick or less. Final board may need to be trimmed to fit.Slide the final board into place from the top.Insert infill materials starting at one side, sliding each board into the next.Top or bottom infill board may need to be trimmed to fit.Continue adding infill materials till you reach the last piece.Insert infill material from top, sliding down into bottom trac.When using tongue & groove planks, insert groove side down, tongue side up.Remove at least 1-1/2” x 1-1/2” (not more than 3”x3”) of material at these corners.Before inserting infill, notch out the first and last pieces of infill materials where corners meet Trac connection points to clear bolt/nut.Insert supplied bolt & nut on each end and hand tighten.Raise Bottom Trac up to Post Tracs and align slotted holes.Clearance is typically too tight to slide Bottom Trac in place after mounting Post Tracs.This helps installation of Bottom Trac when Bottom Trac is to be mounted near ground.Prior to drilling, loosely insert lower ends of Post Tracs into Bottom Trac.Attach Post Trac to post using supplied self-drilling screws.Bottom & Top Tracs are identical and interchangeable. ![]() Place Bottom Trac on ground between posts.Top/Bottom Tracs come in two standard sizes – 72” long & 96” long.Set posts using specified length of Top/Bottom Tracs.Trac mounting points include slotted holes for easy field alignment and assembly. steel for superior strength and durability. Siderails are available to accommodate 48″, 72″ or 96″ panel heights.įenceTrac’s patented U-channel metal fence frames are formed from galvanized 18 ga. Top & bottom rails are available in 72″ or 96″ lengths. The standard fence kit includes: (1) Top Trac, (1) Bottom Trac, (2) Post Trac siderails (for post mount) and hardware to assemble metal components. When using standard FenceTrac, we recommend tongue & groove infill to provide the most strength and privacy. If a piece of infill material gets damaged, simply remove the top rail and slide the old piece out and the new piece in. (Hardware included)įence maintenance is a breeze. Typical installations require just (4) bolts per panel & self-tapping screws to attach Post Trac siderails to each post. ![]() There is no need for hundreds of nails, screws, etc. Simple & fast assembly. Infill materials slide into U-shaped rails.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |